Easy Way to Learn Dsc Alarm System

Download Article

Download Article

DSC alarms can go off for a number of reasons. To reset the alarm or the warning lights, enter your master code twice, press the reset button, and then enter "*72" if the alarm is still ringing. Once the alarm is off, try to find out why it went off. The most common reasons include power failures, intruders, smoke, and problems with the phone line. These simple steps will have your alarm system back to normal in less than 5 minutes!

1. 1

   Open the access door and enter your master code twice. Pull down the panel that covers the keypad on your alarm system. After this, simply enter your 4 digit master code, wait 2 seconds, and then enter it again.^[1]

   • On some models, this step will reset the alarm and stop it from ringing. This step will also reset the trouble light, armed light, and memory light. If your alarm is still ringing, complete the rest of the steps below.

2. 2

   Hold down the reset button for 2 seconds. This button is usually located on the bottom right side of the keypad. Hold it down for at least 2 seconds to disengage the alarm. You will notice the lights on the alarm change from red to green to signal that the alarm has been reset.^[2]

   • This also helps to reset the low battery light once the power has been restored.

   Advertisement

3. 3

   Press "*72" if the alarm is still ringing. Use the keypad to enter the code "*72." This resets the smoke sensors, which will cause the alarm to stop if it is still ringing. If your keypad has an "Enter" button, press this once you have entered the code.

   • If you make a mistake while entering your code, press the pound (#) button, and then start over.

Advertisement

1. 1

   Check for power failure. This is the most common reason for DSC alarms to unexpectedly ring. Check if the lights on the property are working to ascertain if the power is currently on. If the power is out and the alarm is ringing, this indicates that the batteries in the alarm system are dead and need to be replaced.^[3]

   • Contact your power company for information about recent power outages in your area.

2. 2

   Search the area for signs of an intruder. Your DSC alarm system is designed to alert you of unusual motion in and around your property. Check your property for any signs of intrusion, such as broken windows, stolen goods, and dirty footprints inside.^[4]

   • If you have a video monitoring system on your property, check the footage to rule out the possibility of an intruder.

3. 3

   Check for smoke and fire around the property. If you can't find any signs of fire on your property, consider if there has been any smoke that could have triggered the smoke detectors. Burnt toast, birthday candles, and a smoking pot on the stove can sometimes trigger sensitive smoke detectors.^[5]

   • If you had to press "*72" to reset your alarm, this indicates that smoke was most likely the reason for your alarm ringing.

4. 4

   Investigate if the phone lines are working. If your alarm is connected to the phone lines, temporary phone outages can cause the alarm to ring. Call your phone provider from your mobile phone to find out if there have been any phone line problems in your area.^[6]

Advertisement

Add New Question

• Question

  How do I make my DSC alarm stop beeping?

  

  Drew Hawkins1

  Community Answer

  One way you can stop the beeping is to reset the alarm system. Locate the keypad and pull down the panel that covers the keypad on your alarm system. Then, enter your 4 digit master code, wait 2 seconds, and then enter it again. On some models, this step will reset the alarm and stop it from ringing. This step will also reset the trouble light, armed light, and memory light. If the alarm continues to beep, locate the reset button on the bottom right of the keypad and hold it down for at least 2 seconds. The lights should change from red to green and the alarm should stop beeping.

• Question

  How do I reset my alarm panel?

  

  Drew Hawkins1

  Community Answer

  There are a couple of ways you can reset your alarm panel. The simplest is to power it down and then power it back on, which is called a power reset. Open up the panel and look for the power button. Hold it down until the panel turns off and there aren't any lights on. Wait a few seconds and then power it back on by pressing the button again. You can also try unplugging the panel itself to remove it from power and then plug it back in. Another way to reset your panel is to use the reset button. It's usually located on the bottom right of the keypad. Hold it down for a few seconds until the panel lights change color or start blinking. After a few moments it should return to normal.

• Question

  Why is my alarm beeping?

  

  Drew Hawkins1

  Community Answer

  There are a number of possible reasons why your alarm is beeping unexpectedly. The most common reason is a power failure. Check if the lights on the property are working to ascertain if the power is currently on. If the power is out and the alarm is ringing, this indicates that the batteries in the alarm system are dead and need to be replaced. It's also possible that your alarm is doing exactly what it's supposed to do: detect intruders. Check your property for any signs of intrusion, such as broken windows, stolen goods, and dirty footprints inside. If you have a video monitoring system on your property, check the footage to rule out the possibility of an intruder. If your alarm is connected to the phone lines, temporary phone outages can cause the alarm to ring. Call your phone provider from your mobile phone to find out if there have been any phone line problems in your area.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

• Always get your alarm system serviced by a DSC alarm technician, as this keeps your warranty valid. Search online to find a DSC alarm technician in your area.

Thanks for submitting a tip for review!

Advertisement

• If there is a fire, call emergency services before resetting your alarm system.

• If you are searching for an intruder, bring a friend or neighbour with you for safety.

Advertisement

About This Article

Thanks to all authors for creating a page that has been read 117,638 times.

Did this article help you?

faulknerspead1947.blogspot.com

Source: https://www.wikihow.com/Reset-a-DSC-Alarm

Share this post